Author |
Message |
Topic: SDR 200 Setting float height |
frankclock
Replies: 1
Views: 10745
|
Forum: Yamaha Posted: Wed Jun 12, 2019 10:18 am Subject: SDR 200 Setting float height |
Im having trouble getting my bike to run smoothly lowdown
it seems very rich lowdown ticking over very lumpy & at times stalling
its also very rough until it clears out then runs great
ive set ... |
Topic: SDR 200 IGNITION SETTING |
frankclock
Replies: 1
Views: 10187
|
Forum: Yamaha Posted: Sun Sep 02, 2018 5:18 am Subject: SDR 200 IGNITION SETTING |
I have been wanting to check the timing on my bike
I cannot see any marks on the flywheel can someone point me in the right direction as to what to look for
Thanks |
Topic: SDR200 ADJUSTING YPVS |
frankclock
Replies: 9
Views: 19503
|
Forum: Yamaha Posted: Fri Dec 22, 2017 8:21 pm Subject: Power valve FIXED!!! |
Fixed. !!
I just checked my good bike & the valve was miles out
I swapped the cables over & the setting was very close
I have adjusted as it should be so breakfast then a ride before it get ... |
Topic: SDR200 ADJUSTING YPVS |
frankclock
Replies: 9
Views: 19503
|
Forum: Yamaha Posted: Fri Dec 22, 2017 7:39 pm Subject: SDR200 ADJUSTING YPVS |
Thanks mate
It's 5am so a bit early for starting bikes
My 2nd bike does not have a battery so I'll connect something & test that one because that seems to fly
I also noticed on my good ... |
Topic: SDR200 ADJUSTING YPVS |
frankclock
Replies: 9
Views: 19503
|
Forum: Yamaha Posted: Fri Dec 22, 2017 6:22 pm Subject: SDR200 ADJUSTING YPVS |
Thanks mate
It's 5am so a bit early for starting bikes
I'll give it a go in a few hours & let you know
My 2nd bike does not have a battery so I'll connect something & test that one ... |
Topic: SDR200 ADJUSTING YPVS |
frankclock
Replies: 9
Views: 19503
|
Forum: Yamaha Posted: Fri Dec 22, 2017 9:23 am Subject: Sdr |
Thanks again for your help
So if I switch the ign on & let it cycle the slot & hole should be lined up
Should it still be lined up when switched off
If so mine is nowhere close
I'll ... |
Topic: SDR200 ADJUSTING YPVS |
frankclock
Replies: 9
Views: 19503
|
Forum: Yamaha Posted: Fri Dec 22, 2017 12:42 am Subject: SDR POWER VALVE |
Thanks for the info bobbyboy
I figured it was something like that
BUT BUT
When the motor is not running the slot in the pulley is stopped at 11 o clock whereas the hole in the cases is at 1 o ... |
Topic: SDR200 ADJUSTING YPVS |
frankclock
Replies: 9
Views: 19503
|
Forum: Yamaha Posted: Wed Dec 20, 2017 12:26 am Subject: SDR200 ADJUSTING YPVS |
CAN SOMEONE PLEASE TELL ME HOW TO ADJUST THE YPVS
Ihave just ridden my 2nd SDR & it seems to be a rocket compared to my other
On looking at the cable adjusters there seems to be a big differ ... |
Topic: SDR 200 ENGINE |
frankclock
Replies: 2
Views: 12379
|
Forum: Yamaha Posted: Sat Dec 16, 2017 9:45 pm Subject: SDR 200 ENGINE |
I have looked but cannot find any mention of another bike with the same engine as the SDR
It seems unlikely that Yamaha would design a motor just for this model only there seems to be a third engine ... |
Topic: SDR 200 ENGINE MOUNTS HELP NEEDED |
frankclock
Replies: 6
Views: 17370
|
Forum: Yamaha Posted: Fri Dec 15, 2017 4:05 am Subject: my bitsa sdr |
thanks again James for the info
Due to a few days away the bike has not yet been ridden but hopefully this weekend
One thing I have wondered about is the SDR engine has the been derived from an ... |
Topic: SDR 200 ENGINE MOUNTS HELP NEEDED |
frankclock
Replies: 6
Views: 17370
|
Forum: Yamaha Posted: Sun Dec 10, 2017 12:48 am Subject: Engine mounts |
James
Thanks yet again
My main concern were the rear engine mounts which were in a very poor state
I removed the original rubbers & replaced them with HQ Holden top rear shock rubbers which see ... |
Topic: SDR 200 ENGINE MOUNTS HELP NEEDED |
frankclock
Replies: 6
Views: 17370
|
Forum: Yamaha Posted: Fri Nov 17, 2017 9:50 pm Subject: SDR 200 ENGINE MOUNTS HELP NEEDED |
After owning my SDR for close on a year all the little issues seem to have been overcome
So I thought I would look at getting my spare SRD together rather than it being in peices
The chances of a mi ... |
Topic: SDR THROTTLE CABLE |
frankclock
Replies: 0
Views: 11107
|
Forum: Yamaha Posted: Mon Oct 30, 2017 7:14 am Subject: SDR THROTTLE CABLE |
The throttle cable plastic outer adjuster under the twistgrip is broken
Can anyone suggest a cable from another model that will fit
ive seen a dt200 cable perhaps that may fit with a bit of modifica ... |
Topic: SDR CARB SETTINGS HELP |
frankclock
Replies: 2
Views: 11653
|
Forum: Yamaha Posted: Sun Oct 15, 2017 6:50 pm Subject: Carb rebuild |
James
Thanks for the reply
The bike is fixed? after fitting another carburetor
I had my original stripped & cleaned & could not see anything wrong but being unsure I decided to fit the o ... |
Topic: SDR CARB SETTINGS HELP |
frankclock
Replies: 2
Views: 11653
|
Forum: Yamaha Posted: Sat Oct 07, 2017 1:10 am Subject: SDR CARB SETTINGS HELP |
I have had a few problems with my SDR since buying it
The bike seems to be running rich on tickover seeming to be very lumpy
I fitted smaller pilot jet with a bit better result but still not as I ... |
|